House Kolor KD3003 Yellow DTS Epoxy Surfacer Sealer 1Qt Kit

$111.58 USD

( / )

Unavailable

KD3003 Series Kustom DTS (direct to substrate) Foundation Surfacer/Sealer is formulated with a hybrid of epoxy and acrylic polymers, which provide excellent adhesion, good corrosion resistance, productive dry times, and ease of sanding. These DTS surfacer/sealers emit very low amounts of Volatile Organic Compounds (VOCs), Hazardous Air Polluting Solvents (HAPS), and contain no isocyanates. The KD3003 Series DTS surfacer/sealers may be applied to the existing OEM finish, bare steel, aluminum, fiberglass, galvanized surfaces, and various plastics. Its tenacious adhesion, hi-build, excellent durability, and water and corrosion resistance make it a logical choice for the basis of a long lasting custom paint job.

KD3003 Series Kustom DTS Foundation Surfacer/Sealer:

Resists cracking
Cures for sanding and finishing in 60-90minutes at 70oF
Prevents plastic filler staining or bleed through
Does not stain, shrink, or swell from sand scratches

Container: 1 Quart Kit (32oz Primer + 8oz Activator)

Substrate

OEM Finishes
Bare Steel
Bare Aluminum
Bare Fiberglass
Galvanized Surfacers
Various Plastics (Testing For Adhesion Is Recommended)
Body Fillers

Components
KD3003 series of primers were designed to be intermixed with each other to tint the primer closest to the base coat color being applied. This is important in reducing the number of coats of base coat also in the event the finish is chipped or scratched the damage area won t be as obvious. (Refer to mixing chart for formulas)

KD3000 Medium Gray
KD3001 Black
KD3002 White
KD3003 Yellow
KD3004 Red
KD3005 Blue
KDA3000 Activator
RU310 Fast Reducer
RU311 Medium Reducer
RU312 Slow Reducer
RU313 Very Slow Reducer
RU300 Medium Exempt Reducer (1.0 lbs/gal VOC)
RU301 Slow Exempt Reducer (1.0 lbs/gal VOC)

Mixing Ratio
KD3003 Series Kustom DTS Foundation Surfacer/Sealer is a two or three part system. Aggressively mix the KD3003 Series DTS surfacer/sealer thoroughly before activating or reducing. Always measure, do not guess. Stir mixed components well to ensure a thorough cure, use a paint shaker for best results. No incubation time is needed. Shop conditions can vary pot life.

Surfacers For High-Build (HB)
Mix four (4) parts KD3003 Series DTS surfacer/sealer to one (1) part KDA3000 Activator. (4:1 by volume) One Medium Wet Coat Equals Approx. 1.3 mils. Of Film Build.

For Medium-Build (MB)
Mix four (4) parts KD3003 Series DTS surfacer/sealer to one (1) part KDA3000 Activator and reduce with one (1) part Kosmic Reducer. (4:1:1 by volume) One Medium Wet Coat Equals Approx. 1 Mil. Of Film Build.

Sealers
Refer to section on KD3003 Series DTS Surfacer/Sealer (Applied As A Sealer). FOR CALIFORNIA (2.1 lbs/gal VOC) Reduce with RU300 or RU301 Exempt Kosmic Reducers.

Pot Life
As a surfacer 45 to 90 minutes (depending on shop conditions) As a Sealer Refer to section on KD3003 Series DTS Surfacer/Sealer (Applied As A Sealer).

Please select all options.